What are the common failure causes and treatment methods of glue filling machine?
- Categories:News
- Author:
- Origin:
- Time of issue:2022-12-21
- Views:0
(Summary description)Common failure causes and treatment methods of glue filling machine:
First, the mixing head is not glue. Fault cause and treatment:
1. It may be that the glue filling machine is not connected to the air source, resulting in the pneumatic valve can not be opened, so check whether the air source is connected, and determine that the glue filling machine has ventilation.
2. After confirming ventilation, see whether the cylinder of the mixing head can be opened? Manually loosen the cylinder locking screw.
3. Check whether there are still raw materials in the raw material bucket. If not, add glue.
4. Check whether the material pipe mixing and other components are blocked, if blocked, manually dredge the pipeline.
Two, A, B metering pump alarm. Fault cause and treatment:
1. If the material pipe is blocked and the pressure of the material pipe is too large, the system will automatically alarm and prompt us to replace the pipe at this time.
2. The mixing head cylinder is not opened, and the glue can not be produced. There will also be an alarm warning, and the mixing head needs to be checked.
3. The line of the servo motor encoder is in bad contact or disconnected, check the line or disconnected and reconnect.
Three, the amount of glue is not allowed. Fault cause and treatment:
1. Too little spare material in the barrel will lead to incorrect amount of glue, so glue needs to be added.
2. The inlet of A and B metering pumps is blocked. It is necessary to check and clean the filter screen in front of the metering pump.
3. The parameters of A and B metering pumps are modified artificially, so it is necessary to test and set the parameters again.
Four, the mixing head does not stir. Fault cause and treatment:
1. Check whether the stirring blade is broken, and replace it with a new one.
2. If the steel hook above the mixing leaf falls off, it will also cause no mixing. Check and hang it up.
3. If it is a dynamic mixing head, it is also necessary to check whether the stirring motor runs normally, whether the line is disconnected, and whether the controller works normally.
Five, mixed head alarm. Fault cause and treatment:
1. First, check whether the hook on the mixing leaf is glued to death, resulting in the failure of rotation. Rotate the hook by hand, if it does not move, disassemble and clean it up.
2. If the code line is in poor contact, check the line or disconnect and reconnect.
What are the common failure causes and treatment methods of glue filling machine?
(Summary description)Common failure causes and treatment methods of glue filling machine:
First, the mixing head is not glue. Fault cause and treatment:
1. It may be that the glue filling machine is not connected to the air source, resulting in the pneumatic valve can not be opened, so check whether the air source is connected, and determine that the glue filling machine has ventilation.
2. After confirming ventilation, see whether the cylinder of the mixing head can be opened? Manually loosen the cylinder locking screw.
3. Check whether there are still raw materials in the raw material bucket. If not, add glue.
4. Check whether the material pipe mixing and other components are blocked, if blocked, manually dredge the pipeline.
Two, A, B metering pump alarm. Fault cause and treatment:
1. If the material pipe is blocked and the pressure of the material pipe is too large, the system will automatically alarm and prompt us to replace the pipe at this time.
2. The mixing head cylinder is not opened, and the glue can not be produced. There will also be an alarm warning, and the mixing head needs to be checked.
3. The line of the servo motor encoder is in bad contact or disconnected, check the line or disconnected and reconnect.
Three, the amount of glue is not allowed. Fault cause and treatment:
1. Too little spare material in the barrel will lead to incorrect amount of glue, so glue needs to be added.
2. The inlet of A and B metering pumps is blocked. It is necessary to check and clean the filter screen in front of the metering pump.
3. The parameters of A and B metering pumps are modified artificially, so it is necessary to test and set the parameters again.
Four, the mixing head does not stir. Fault cause and treatment:
1. Check whether the stirring blade is broken, and replace it with a new one.
2. If the steel hook above the mixing leaf falls off, it will also cause no mixing. Check and hang it up.
3. If it is a dynamic mixing head, it is also necessary to check whether the stirring motor runs normally, whether the line is disconnected, and whether the controller works normally.
Five, mixed head alarm. Fault cause and treatment:
1. First, check whether the hook on the mixing leaf is glued to death, resulting in the failure of rotation. Rotate the hook by hand, if it does not move, disassemble and clean it up.
2. If the code line is in poor contact, check the line or disconnect and reconnect.
- Categories:News
- Author:
- Origin:
- Time of issue:2022-12-21
- Views:0
Common failure causes and treatment methods of glue filling machine:
First, the mixing head is not glue. Fault cause and treatment:
1. It may be that the glue filling machine is not connected to the air source, resulting in the pneumatic valve can not be opened, so check whether the air source is connected, and determine that the glue filling machine has ventilation.
2. After confirming ventilation, see whether the cylinder of the mixing head can be opened? Manually loosen the cylinder locking screw.
3. Check whether there are still raw materials in the raw material bucket. If not, add glue.
4. Check whether the material pipe mixing and other components are blocked, if blocked, manually dredge the pipeline.
Two, A, B metering pump alarm. Fault cause and treatment:
1. If the material pipe is blocked and the pressure of the material pipe is too large, the system will automatically alarm and prompt us to replace the pipe at this time.
2. The mixing head cylinder is not opened, and the glue can not be produced. There will also be an alarm warning, and the mixing head needs to be checked.
3. The line of the servo motor encoder is in bad contact or disconnected, check the line or disconnected and reconnect.
Three, the amount of glue is not allowed. Fault cause and treatment:
1. Too little spare material in the barrel will lead to incorrect amount of glue, so glue needs to be added.
2. The inlet of A and B metering pumps is blocked. It is necessary to check and clean the filter screen in front of the metering pump.
3. The parameters of A and B metering pumps are modified artificially, so it is necessary to test and set the parameters again.
Four, the mixing head does not stir. Fault cause and treatment:
1. Check whether the stirring blade is broken, and replace it with a new one.
2. If the steel hook above the mixing leaf falls off, it will also cause no mixing. Check and hang it up.
3. If it is a dynamic mixing head, it is also necessary to check whether the stirring motor runs normally, whether the line is disconnected, and whether the controller works normally.
Five, mixed head alarm. Fault cause and treatment:
1. First, check whether the hook on the mixing leaf is glued to death, resulting in the failure of rotation. Rotate the hook by hand, if it does not move, disassemble and clean it up.
2. If the code line is in poor contact, check the line or disconnect and reconnect.
Scan the QR code to read on your phones
Copyright © Nantong Fuling Machine Electric Technology Co., LTD. All Rights Reserved Powered by www.300.cn SEO
